{"title":"Signal Routing \u0026 Utility","description":null,"products":[{"product_id":"lehle-little-dual-ii","title":"Lehle Little Dual II","description":"• ABY switcher (A or B or both)\u003cbr\u003e• Hum and noise-free switching\u003cbr\u003e• High-impedance LEHLE TRANSFORMER HZ with phase and ground switch\u003cbr\u003e• Two different operating modes\u003cbr\u003e• Stereo-routing option\u003cbr\u003e• Active pop suppression circuit\u003cp\u003eThe LEHLE LITTLE DUAL II is the successor to the Lehle Little Dual and is a maximum signal-fidelity amp switcher for two amps. By using the soft-touch switches you can switch between two connected amplifiers hum-free and without sound loss.\u003c\/p\u003e\u003cp\u003eTwo different operating modes are ready for you. You decide if you want to activate or deactivate every output individually or if you want to switch between the amps and activate the remaining one.\u003cbr\u003eThe LEHLE-Switches work with a microcontroller and an intelligent True-Bypass-Relay-Circuit with active pop noise suppression circuit. Thereby they switch the LEHLE LITTLE DUAL II even faster than mechanical switches and in addition to that wear- and noise-free.\u003c\/p\u003e\u003cp\u003eThe easy-action mushroom-shaped buttons characteristic of LEHLE products are mounted in the cover, so that your foot pressure is transmitted indirectly only, via a spring. Thus the electronics board is not exposed to mechanical loads, making the LEHLE LITTLE DUAL II virtually indestructible and guaranteeing years of trouble-free switching.\u003cbr\u003eHigh-intensity LEDs make it easy to read off switching state A or B, or both, even under high-power spots.\u003cbr\u003eThe centrepiece of the LEHLE LITTLE DUAL II is its high-end LEHLE TRANSFORMER HZ, which galvanically isolates output A from output B, making history of hum loops - permanently! The LEHLE LITTLE DUAL II features a gold-plated contact phase inverter and a gold-plated contact ground switch. The two inputs can also be routed in stereo to outputs A and B, if you use the stereo signal of an effects unit as the input, for example. This also makes it possible to route instruments equipped with two pickups, including many acoustic and hybrid guitars, and also double basses, via two amplifier systems - with no complications.\u003c\/p\u003e\u003cp\u003eAdditionally the LEHLE LITTLE DUAL II is equipped with a TRS switch. Therewith it is possible to send in above-mentioned stereo- or dual-mono signals via a TRS jack or “stereo-jack”.\u003cbr\u003eThese signals can be operated either in alternation or in parallel - without hum, and without sound losses, needless to say. The LEHLE LITTLE DUAL II - small, but so utterly effective!\u003c\/p\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47503300395092,"sku":"210000006030","price":399.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/dual-1.png?v=1786905859"},{"product_id":"suhr-ace-analog-cabinet-emulator","title":"Suhr ACE Analog Cabinet Emulator","description":"\u003cp\u003eThe A.C.E. (Analog Cabinet Emulator) is an active analog cabinet emulator designed to offer guitarists a portable and convenient way to capture the complex characteristics of a guitar speaker cabinet for a variety of recording (silent* or in a studio) and live performance applications without the use of a microphone.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMoving Analog Forward\u003cbr\u003e\u003c\/strong\u003e\u003cbr\u003e100% pure analog signal path from start to finish, the A.C.E. employs an advanced Multi-StageFiltering (MSF) network to generate stunningly realistic speaker cabinet simulations that capture\/bring to life all the warmth, punch and character of a mic’d speaker cabinet to any performance without the assistance of DSP (digital signal processing).\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMusically Versatile\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA.C.E.’s on-board filtering controls is not your run of the mill EQ. Each control (Subs, Highs andPresence) was carefully voiced to offer a musical range of tone shaping (versatility) without becoming unrealistic, synthetic or fatiguing when crafting\/fine tuning your desired\/ideal cabinet response.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eReady For Anything\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFully equipped with a comprehensive set of interface features, A.C.E. makes it easy to connect with a variety of recording and sound reinforcement equipment for any situation.\u003c\/p\u003e\u003cp\u003eA.C.E. features dedicated Amplifier and Line Level inputs, a 1\/4” (unbalanced) and XLR (balanced) DI\/Line Output section complete with Phase and Ground Lift functions for the XLR output, a 1\/4” Thru output and last but not least, optimized 18 Vdc circuitry for maximum headroom and dynamic range.\u003c\/p\u003e\u003cp\u003eWhether you are in the studio or on the road, the A.C.E. is sure to become an invaluable tool to delivering a flexible variety of emulated cabinet simulations consistently, every time.\u003c\/p\u003e\u003cp\u003eSPECIFICATIONS\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFEATURES\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e• Active Analog Cabinet Emulator • Multi-Stage Filtering (MSF) Cabinet Emulation (bypassable) • Unbalanced 1\/4″ \u0026amp; Balanced XLR Line Out Section • Phase and Ground Lift For XLR Output • Optimized 18-Volt Circuitry For Maximum Headroom and Dynamic Range • Compact Half Rack Enclosure\u003c\/p\u003e\u003cp\u003e* A.C.E. is not a load device. Make sure your amplifier is connected to a suitable load (Suhr Reactive Load) or speaker cabinet when using A.C.E. to avoid damage.\u003c\/p\u003e","brand":"Suhr","offers":[{"title":"Default Title","offer_id":47503305867348,"sku":"210000009711","price":433.55,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/Untitled25.png?v=1786905925"},{"product_id":"lehle-dual-sgos","title":"Lehle Dual SGOS","description":"\u003cdiv class=\"lz-desc\"\u003e\n\u003cp\u003eThe Lehle Dual SGoS is the second evolutionary stage of the highly successful programmable switcher for two amps plus tuner. This unit makes it possible to play through two amplifiers individually or simultaneously, either as a stand-alone unit or in a network with other Lehle SGoS switchers. A particularly popular combination is the Lehle Dual SGoS with the Lehle D.Loop SGoS. Programming is as easy and intuitive as you would expect from a Lehle product, and can also be done remotely, using MIDI program change commands.\u003c\/p\u003e\n\u003cp\u003eHum loops are completely excluded, thanks to electrical isolation of outputs A and B by the Lehle LTHZ high-end transformer. Gold-plated-contact relays, ground switches and phase inverters assure the full, loss-free guitar sound. The potentiometers are in the signal path when output A and B are active simultaneously, and the volume of the two amps can be balanced - producing a third sound you've never heard before! Output T, basically intended for instrument tuners, can also be used for a third amp or for a second channel for amp B, opening up even more potentials.\u003cbr\u003e\nThe gold-plated-contact relays feature active pop-and-click suppression, outputs A and B can be muted for undisturbed instrument tuning. Welcome to the new Duality!\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47503308685396,"sku":"210000012015","price":514.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/Untitled35.png?v=1786905860"},{"product_id":"lehle-p-iso","title":"Lehle P-ISO","description":"\u003cp\u003eThe LEHLE P-ISO combines passive isolation with the highest possible signal fidelity. Its applications range from isolation and eliminating hum, to balancing and reamplification along with any signal routing that requires a clean signal free from noise. At its core is the high-end LEHLE TRANSFORMER HZ, which galvanically isolates the signal, eliminating any possibility of ground loops. The LEHLE TRANSFORMER HZ was specially designed for use with high-impedance signals but also processes low-impedance signals with uncompromising sound quality. The classic application for the LEHLE P-ISO is as a hum suppressor. Frequently background noise caused by ground loops occurs when two electronic devices are connected to each other. The LEHLE P-ISO provides a simple, but extremely effective remedy when installed between the two units. Using the ISO output, the devices are galvanically isolated and background noise becomes a thing of the past. By using two amplifiers, driven by one stereo effects device, the LEHLE P-ISO can successfully isolate one amplifier from the other. Thanks to its ability to pick off an unbalanced or balanced signal on the ISO output, the Lehle P-ISO is also eminently suitable as a reamplification device or as a high-quality compact DI box for all signal types. And just in case you are looking for a power connection: the LEHLE P-ISO performs all its functions without any need for a power supply. And due to its optimised size and low weight, it fits easily below your pedalboard or in any pocket.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIsolator and DI box\u003c\/li\u003e\n\u003cli\u003eAbsolutely no signal loss or hum\u003c\/li\u003e\n\u003cli\u003eHigh-impedance LEHLE TRANSFORMER HZ\u003c\/li\u003e\n\u003cli\u003eSuitable for balanced or unbalanced signals\u003c\/li\u003e\n\u003cli\u003ePassive – no need for a power supply\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47503308718164,"sku":"210000012018","price":179.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/Lehle-P-ISO-06_800x800_0ed64af4-76d3-422f-80af-d752c784c462.jpg?v=1786905780"},{"product_id":"little-lehle-ii","title":"Little Lehle II","description":"\u003cdiv class=\"lz-desc\"\u003e\n\u003cp\u003eThe Little Lehle II removes effect pedals from the signal path at the press of its button. A signal can be picked off at any point in the signal chain, to switch to an instrument tuner, for example.\u003cbr\u003e\nThe Little Lehle II can also be used to switch between two instruments on one amp or, vice versa, between two amps with one instrument. Extremely diverse sound sources are possible - signals from pick-ups, microphones and keyboard line-out sockets are routed loss-free to the target amplifier or recorders, and all jack sockets are stereo. Switches with gold-plated contacts assure True Bypass. As on this unit's \"big brother\", the Lehle D.Loop SGoS, not only the stereo signal, but also the signal ground, is switched - so it's goodbye to hum when switching between two amps, and selecting effect loops - it just can't happen any more!\u003cbr\u003e\nThe easy-action mushroom-shaped button characteristic of Lehle products is mounted in the cover, so that your foot pressure is transmitted indirectly, via only a spring, to the slide switch with its gold-plated contacts. The electronics board is thus not exposed to mechanical loads, making the Little Lehle II virtually indestructible and guaranteeing years of trouble-free switching.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47503309439060,"sku":"210000012167","price":210.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/LehleLittleLehleII_1.jpg?v=1786905973"},{"product_id":"jackson-audio-amp-mode-mosfet-boost","title":"Jackson Audio Amp Mode MOSFET Boost","description":"\u003cdiv class=\"lz-desc\"\u003e\n\u003cp\u003eThe AMP MODE Boost is a MOSFET transistor boost and is the exact same circuit that is found in our best selling PRISM Preamp! Ask anyone who owns a PRISM and they'll most likely tell you that their favorite mode of the PRISM is the AMP MODE.\u003c\/p\u003e\n\u003cp\u003eSince we released the PRISM in 2016, we have been inundated with requests to come out with a stand-alone product based on the AMP MODE of the PRISM. You asked and we listened!\u003c\/p\u003e\n\u003cp\u003eKeep reading to learn more about the AMP MODE!\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Jackson Audio","offers":[{"title":"Default Title","offer_id":47503309963348,"sku":"210000012714","price":199.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/amp.png?v=1786905856"},{"product_id":"oto-bebe-cherie-analog-mixer","title":"OTO Bébé Chérie Analog Mixer","description":"\u003cp\u003e\u003cstrong\u003eBébé Chérie\u003c\/strong\u003e is a 6-channel stereo analog mixer with a one-knob compressor and a Bliss enhancer on the master bus.\u003c\/p\u003e\u003cp\u003eThe first 4 channels offer a variable input gain (up to 34 dB) with an asymmetrical diode clipper for smooth and musical distortion.\u003cbr\u003eThe Tilt pot is a simple yet powerful one-knob equalizer : boosting the lows while attenuating the highs when the pot is turned down, attenuating the lows while boosting the highs when the pot is turned up.\u003cbr\u003eWhen the Tilt pot is in its center position, the equalizer is flat.\u003cbr\u003eThe rear panel switch selects the type of inputs : TRS for stereo sources and TS for mono (the signal is center panned).\u003c\/p\u003e\u003cp\u003eThe last 2 channels include a 2 bands Baxandall equalizer, the input gain can be set between 0 and +10 dB using the rear panel switch.\u003cbr\u003eThere’s no distortion on these 2 channels so you can use them when you want to keep a clean sound.\u003c\/p\u003e\u003cp\u003eThe compressor has a 3:1 ratio with a fast attack and a mid release times, perfect for mixdown compression.\u003cbr\u003eVery easy to operate, it will give you good results with many kinds of music styles.\u003cbr\u003eThe Bliss pot controls a hi frequency enhancer circuit and is very useful for adding air and punch to your mix, specially when your using large amount of compression.\u003c\/p\u003e\u003cp\u003eWhenever a channel is muted, the signal is routed to the Alternate output. You can use this output for recording purposes or for sending the channel to an external effect.\u003c\/p\u003e\u003cp\u003eThe Phones output is based on an unity gain, low noise and low distortion Texas Instruments© amplifier. This output is a copy of the master output (with compression and Bliss), so you can also use it as a second output.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBébé Chérie\u003c\/strong\u003e uses the best quality parts : ALPS© pots, high-performance operational amplifiers, audiophile Panasonic© film capacitors, THAT Corporation© VCAs, Switchcraft© 3.5 mm connectors, metal enclosure.\u003cbr\u003eThe power supply is internally boosted to +\/- 12 volts for pro audio headroom.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBébé Chérie\u003c\/strong\u003e is specially designed for mixing 3.5 mm stereo Jacks sources, but can be used with any device using adapters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBébé Chérie\u003c\/strong\u003e is a very versatile box and can be used in many ways : mixer for compact live, analog summing for your audio interface, effect box (distortion, equalization, compression,…)\u003c\/p\u003eFEATURES\u003cp\u003e• Full analog mixer\u003cbr\u003e• 4 channels with variable gain up to +34 dB, asymmetrical soft clipping and a tilt eq\u003cbr\u003e• 2 channels with Baxandall 2 bands eq and a 0\/+10 dB selectable input gain\u003cbr\u003e• 3:1 ratio one-knob compressor on the master bus\u003cbr\u003e• Bliss hi frequency enhancer on the master bus\u003cbr\u003e• Unity gain Hi Fidelity phones out. Can be used as a second master output\u003cbr\u003e• Alternate output : whenever a channel is muted, it is routed to the Alt. Out\u003cbr\u003e• 24 volts internal power supply for pro audio dynamic range\u003cbr\u003e• Rugged Switchcraft© 3.5 mm stereo mini-jack connectors\u003cbr\u003e• Audiophile film capacitors used in the eq circuitry, low noise and low distortion op amp on the audio path, THAT Corporation© VCAs, ALPS© pots\u003cbr\u003e• Dimensions : 290 x 145 x 62 mm, Weight : 1338 g\u003cbr\u003e• Power supply included\u003c\/p\u003e","brand":"Oto","offers":[{"title":"Default Title","offer_id":47503316385876,"sku":"210000017554","price":1045.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/bebe-cherie.png?v=1786905813"},{"product_id":"little-lehle-iii","title":"Little Lehle III","description":"\u003cp\u003e• True Bypass effects looper and AB switch\u003cbr\u003e• Hum-free and noiseless switching\u003cbr\u003e• Three different operating modes: Latching, Momentary or Mixed Mode\u003cbr\u003e• Mono and stereo functionality\u003cbr\u003e• Active pop suppression circuit\u003c\/p\u003e\u003cp\u003eThe \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e - The universal Lehle switching and looping tool.\u003cbr\u003eThe \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e allows you to remove effects pedals from your signal path at the press of a button.\u003cbr\u003eA signal can be picked off at any point in the signal chain, for example allowing you to switch to an instrument tuner. The \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e can also be used to switch between two instruments with one amp or, vice versa, between two amps with one instrument. Extremely diverse sound sources are no problem. Signals from pickups, microphones and keyboard line-out sockets are routed loss-free to a target amplifier or recorder. All jack sockets are stereo, so you can re-route balanced signals too.\u003cbr\u003eWith the release of the \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e you can now combine mono and stereo signals. This will allow you to integrate an effects pedal with a mono input and stereo output into the signal path of the \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e without limitations. The LEHLE-Switch works with a microcontroller and an intelligent true bypass relay circuit with an active pop suppression function, thereby allowing the \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e to switch even faster than mechanical switches, noise free and without wear.\u003cbr\u003eThe easy-action mushroom-shaped button characteristic of LEHLE products is mounted in the cover so that your foot pressure is transmitted indirectly via a spring. Thus the circuit board is not exposed to mechanical loads, making the \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e virtually indestructible and guaranteeing years of trouble-free switching.\u003cbr\u003eNot only is the stereo signal switched, but also the earth, - so say ‘goodbye’ to hum when switching between two amps, and selecting effect loops - it just can't happen anymore.\u003cbr\u003eNew for the \u003cstrong\u003eLittle Lehle III\u003c\/strong\u003e are the three operating modes, making the switch work as either a latching or momentary switch, allowing for short or rhythmic stutter-effects. The third mode combines a mixture of operating mode one and two: a short hit engages the latching function and a long hit is momentary.\u003cbr\u003eThink of the creative potential. We take care of your signal so that you can take care of the music.\u003c\/p\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47503316779092,"sku":"210000017705","price":249.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/Little-Lehle-III-06_800x800_10b15995-1d65-4dc2-8226-e893eb97107e.jpg?v=1786905726"},{"product_id":"vertex-effects-buffer-interface","title":"Vertex Effects Buffer Interface","description":"Features include\u003cul class=\"list-unstyled\"\u003e\n\u003cli\u003eInput Impedance: 1M ohms\u003c\/li\u003e\n\u003cli\u003eOutput Impedance: 80 ohms\u003c\/li\u003e\n\u003cli\u003eDC Input Voltage Range: 5.5V-30V (150mA)\u003c\/li\u003e\n\u003cli\u003eNumber of Buffers: 4 (Input, Amp L Out, Amp R Out, Return)\u003c\/li\u003e\n\u003cli\u003eIsolated Output: Yes (transformer-based isolation on AMP R output)\u003c\/li\u003e\n\u003cli\u003ePolarity Switch: Yes (on AMP R output)\u003c\/li\u003e\n\u003cli\u003eDimensions: 5.0\" (L) x 3.0\" (W) x 1.33\" (H)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFor over a decade, every buffer that's come out of Vertex Effects has been custom made, bespoke, for the pedalboard it was designed for or the customer that ordered it. Needless to say, our buffers were very limited, with only a few hundred made over the last ten years. Over that time, and through hundreds of custom buffer interfaces being made, several common applications for buffer combinations and routing emerged as the most common uses as it comes to placing buffers on a pedalboard for the most optimal results. Routing schemes such as mono, stereo, audition loops (inserts), four-cable method, five-cable method, and wet\/dry\/wet were all common requests from our customers, but there was never an all-in-one solution that provided all of these options for buffering and routing your pedalboard in a pedalboard-friendly enclosure - until now.\u003c\/p\u003e","brand":"Vertex Effects","offers":[{"title":"Default Title","offer_id":47503317106772,"sku":"210000017784","price":349.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/656_603.png?v=1786905805"},{"product_id":"eventide-mixing-link-mic-preamp-and-fx-loop","title":"Eventide Mixing Link Mic PreAmp and FX Loop","description":"\u003cp id=\"h-high-quality-mic-pre-with-fx-loop\" class=\"wp-block-heading has-text-align-center has-white-color has-text-color\"\u003e\u003cstrong\u003eHigh-quality Mic Pre with FX Loop\u003c\/strong\u003e\u003c\/p\u003e\u003cp class=\"has-white-color has-text-color\"\u003eA stompbox-size audio toolkit for on-stage, in the studio, and everywhere in between. Includes a quiet high gain mic-pre, 48V phantom power, and enough I\/O and control for applications such as FX Loop for microphone signal processing (vocals, horns, strings, etc), signal splitting, and combining, complete re-amp setup, impedance, and gain matching, mixing and more.\u003c\/p\u003e\u003cul class=\"wp-block-list\"\u003e\n\u003cli\u003e\n\u003cstrong\u003eLatching or momentary\u003c\/strong\u003e footswitch control of FX loop for performance effects\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with a wide range\u003c\/strong\u003e of microphones including condenser and ribbon mics with up to 65dB of clean gain\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAux I\/O \u003c\/strong\u003econnection supporting stereo input and send\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGuitar\u003c\/strong\u003e \u003cstrong\u003eamp\u003c\/strong\u003e \u003cstrong\u003eoutput\u003c\/strong\u003e and \u003cstrong\u003eheadphone\u003c\/strong\u003e \u003cstrong\u003emonitor\u003c\/strong\u003e \u003cstrong\u003eoutput\u003c\/strong\u003e with separate master volume control\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternational\u003c\/strong\u003e \u003cstrong\u003euniversal\u003c\/strong\u003e \u003cstrong\u003epower\u003c\/strong\u003e \u003cstrong\u003esupply\u003c\/strong\u003e included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperates on\u003c\/strong\u003e \u003cstrong\u003e9V battery\u003c\/strong\u003e (no phantom power when operating on a battery)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48V\u003c\/strong\u003e \u003cstrong\u003ephantom\u003c\/strong\u003e \u003cstrong\u003epower\u003c\/strong\u003e for condenser mics\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced\u003c\/strong\u003e \u003cstrong\u003eXLR\u003c\/strong\u003e output which supports DI and line levels\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstrument\u003c\/strong\u003e \u003cstrong\u003eand\u003c\/strong\u003e \u003cstrong\u003ebalanced\u003c\/strong\u003e \u003cstrong\u003eline\u003c\/strong\u003e \u003cstrong\u003elevel\u003c\/strong\u003e inputs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVersatile\u003c\/strong\u003e\u003cstrong\u003emix\u003c\/strong\u003e\u003cstrong\u003econtrol\u003c\/strong\u003e supports 3 modes\u003cul class=\"wp-block-list\"\u003e\n\u003cli\u003e100% Dry w\/FX blended in\u003c\/li\u003e\n\u003cli\u003eMic\/FX balance control\u003c\/li\u003e\n\u003cli\u003e100% FX (no Dry)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eventide","offers":[{"title":"Default Title","offer_id":47503323299924,"sku":"210000019742","price":477.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/MixingLink-registered-743x914-1.jpg?v=1786905671"},{"product_id":"lehle-d-loop-sgos","title":"Lehle D Loop sGos","description":"\u003cp\u003eTwo independent true-bypass loops switched on gold-plated relays, with the signal ground switched as well so the loops do not hum. Jacks and internal routing are fully stereo, which is the reason to reach for this over a simpler looper when there is a rack unit or a stereo pedal in the chain.\u003c\/p\u003e\u003cp\u003eThe buffer is switchable with gain adjustable to +12 dB, and a pop-and-click suppression circuit handles the switching noise. SGoS is Lehle's second generation of switching, so it receives MIDI program changes, sends them, and synchronises with other SGoS units.\u003c\/p\u003e\u003cp\u003eSPECIFICATIONS\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLoops:\u003c\/strong\u003e Two independent true-bypass loops, gold-plated relays\u003cbr\u003e\u003cstrong\u003eRouting:\u003c\/strong\u003e Fully stereo jacks and internal signal path\u003cbr\u003e\u003cstrong\u003eGround:\u003c\/strong\u003e Switched signal ground to eliminate loop hum\u003cbr\u003e\u003cstrong\u003eBuffer:\u003c\/strong\u003e Switchable, gain adjustable to +12 dB\u003cbr\u003e\u003cstrong\u003eSwitching:\u003c\/strong\u003e Pop-and-click suppression\u003cbr\u003e\u003cstrong\u003eMIDI:\u003c\/strong\u003e Receives and sends program changes, syncs with other SGoS switchers\u003c\/p\u003e","brand":"Lehle","offers":[{"title":"Default Title","offer_id":47586460532820,"sku":"210000006027","price":399.95,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0700\/1220\/7188\/files\/LehleDLoopsGos_6.jpg?v=1788842415"}],"url":"https:\/\/lauzonmusic.com\/collections\/utility-effects.oembed","provider":"Lauzon Music","version":"1.0","type":"link"}